Hab mal kurz was anderes probiert. Test Snap runtergehauen, 6.4GB 2,5" Platte ran, ext2, alle bootoptionen aus (bis auf ide, swap und avia watchdog), synchronschreiben beide aus und Ringpuffer auf 90
Aufnahme kommt schon weiter als sonst.
Das LOG ist von der neuen Konfiguration
<4>Linux version 2.4.33.3-dbox2 (vom Jtg-Team) (gcc version 3.4.4) #1 So 12. Nov 16:22:50 CET 2006
<4>On node 0 totalpages: 8192
<4>zone(0): 8192 pages.
<4>zone(1): 0 pages.
<4>zone(2): 0 pages.
<4>Kernel command line: console=tty root=/dev/mtdblock2 rootfstype=squashfs
<4>Decrementer Frequency = 252000000/60
<5>m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
<5>m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
<4>Console: colour dummy device 80x25
<4>Calibrating delay loop... 66.96 BogoMIPS
<6>Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)
<6>Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
<6>Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<6>Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
<4>Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
<4>POSIX conformance testing by UNIFIX
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<4>Starting kswapd
<6>devfs: v1.12c (20020818) Richard Gooch (
rgooch@atnf.csiro.au)
<6>devfs: boot_options: 0x1
<6>JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
<6>squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>i2c-core.o: i2c core module version 2.6.1 (20010830)
<6>i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
<7>i2c-core.o: driver i2c-dev dummy driver registered.
<6>CPM UART driver version 0.04
<6>ttyS0 at 0x0280 is on SMC1 using BRG1
<6>ttyS1 at 0x0380 is on SMC2 using BRG2
<4>pty: 256 Unix98 ptys configured
<6>eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1b:05:e1
<6>loop: loaded (max 8 devices)
<5>D-Box 2 flash driver (size->0x800000 mem->0x10000000)
<6>D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
<4> Intel/Sharp Extended Query Table at 0x0035
<5>cfi_cmdset_0001: Erase suspend on write enabled
<7>0: offset=0x0,size=0x4000,blocks=8
<7>1: offset=0x20000,size=0x20000,blocks=63
<5>Creating 6 MTD partitions on "D-Box 2 flash memory":
<5>0x00000000-0x00020000 : "BR bootloader"
<5>0x00020000-0x00040000 : "FLFS (U-Boot)"
<5>0x00040000-0x006a0000 : "root (SquashFS)"
<5>0x006a0000-0x00800000 : "var (JFFS2)"
<5>0x00020000-0x00800000 : "Flash without bootloader"
<5>0x00000000-0x00800000 : "Complete Flash"
<6>Linux video capture interface: v1.00
<6>mice: PS/2 mouse device common for all mice
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP
<6>IP: routing cache hash table of 512 buckets, 4Kbytes
<6>TCP: Hash tables configured (established 2048 bind 4096)
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<4>VFS: Mounted root (squashfs filesystem) readonly.
<6>Mounted devfs on /dev
<6>Freeing unused kernel memory: 60k init
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
<6>ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
<6>dboxide: $Id: main.c,v 1.10 2006/10/04 00:36:41 carjay Exp $
<3>ide: late registration of driver.
<4>dboxide: activating cs2
<6>dboxide: address space of DBox2 IDE CPLD is at: 0xc38bb000
<6>Probing IDE interface ide0...
<4>hda: HITACHI_DK239A-65B, ATA DISK drive
<7>Unhandled interrupt 2f, disabled
<4>ide0 at 0x010-0x017,0x04e on irq 47
<4>hda: attached ide-disk driver.
<4>hda: host protected area => 1
<6>event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
<6>hda: 12594960 sectors (6449 MB) w/512KiB Cache, CHS=13328/15/63
<6>Partition check:
<6> /dev/ide/host0/bus0/target0/lun0: p1 p2
<6>Adding Swap: 60468k swap-space (priority -1)
<6>[i2c-8xx]: mpc 8xx i2c init
<7>i2c-dev.o: Registered 'PowerPC 8xx I2C adapter' as minor 0
<7>i2c-core.o: adapter PowerPC 8xx I2C adapter registered as adapter 0.
<6>[i2c-8xx]: adapter: 0
<7>i2c-core.o: driver DBox2 Frontprocessor driver registered.
<6>Journalled Block Device driver loaded
<7>i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [PowerPC 8xx I2C adapter](pos. 0).
<7>i2c-core.o: driver i2c audio/video switch driver registered.
<7>i2c-core.o: client [CXA2092] registered to adapter [PowerPC 8xx I2C adapter](pos. 1).
<7>i2c-core.o: driver saa7126 registered.
<7>i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos. 2).
<4>hda: drive_cmd: status=0x53 { DriveReady SeekComplete Index Error }
<4>hda: drive_cmd: error=0x04 { DriveStatusError }
<6>$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
<7>i2c-core.o: driver DBox2-CAM registered.
<7>i2c-core.o: client [DBox2-CAM] registered to adapter [PowerPC 8xx I2C adapter](pos. 3).
<6>$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
<4>DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
<7>i2c-core.o: driver DVB I2C bridge registered.
<7>i2c-core.o: client [DVB I2C bridge] registered to adapter [PowerPC 8xx I2C adapter](pos. 4).
<6>dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
<6>$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
<6>avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
<6>avia_av: AVIA500 sptsfix is off
<4>avia_av_core: Starting avia_av_wdt thread.
<6>avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
<4>avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
<6>avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
<6>avia_gt_core: autodetecting chip type... GTX
<6>avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
<6>avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
<6>avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
<6>avia_gt_ucode: loaded ucode v00F0
<6>avia_gt_ucode: ucode section filters disabled.
<5>avia_gt_core: masking unhandled irq reg 0 bit 1
<5>avia_gt_core: masking unhandled irq reg 0 bit 6
<4>avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
<6>avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
<6>avia_gt_gv: set_input_size (width=720, height=576)
<6>avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
<4>avia_gt_pcm_set_rate(44100)
<6>avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
<6>avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
<6>avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
<5>avia_gt_core: Loaded AViA eNX/GTX driver
<5>avia_gt_core: masking unhandled irq reg 1 bit 11
<5>avia_gt_core: masking unhandled irq reg 1 bit 13
<6>avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
<6>avia_gt_gv: set_input_mode (mode=2)
<6>avia_gt_gv: set_input_size (width=720, height=576)
<6>avia_gt_gv: set_input_mode (mode=2)
<6>avia_gt_gv: set_input_size (width=720, height=576)
<6>avia_gt_gv: set_input_mode (mode=2)
<6>avia_gt_gv: set_input_size (width=720, height=576)
<4>Console: switching to colour frame buffer device 82x32
<6>avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
<4>lcd.o: init lcd driver module
<4>lcd.o: found KS0713/SED153X lcd interface
<6>avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
<6>avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
<6>avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
<4>avia_gt_pcm_set_rate(44100)
<4>avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
<4>DVB: VES1820(0): pwm=0x48
<4>DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
<6>avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
<6>avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
<5>avia_gt_core: masking unhandled irq reg 0 bit 7
<6>avia_gt_gv: set_input_mode (mode=2)
<6>avia_gt_gv: set_input_size (width=720, height=576)
<6>PES, queue 0 normal.
<6> /dev/ide/host0/bus0/target0/lun0: p1 p2
<6> /dev/ide/host0/bus0/target0/lun0: p1 p2
<6>Adding Swap: 60468k swap-space (priority -2)
<4>hda: drive_cmd: status=0x53 { DriveReady SeekComplete Index Error }
<4>hda: drive_cmd: error=0x04 { DriveStatusError }
<6>PES, queue 0 normal.
<5>avia_gt_core: masking unhandled irq reg 1 bit 15
<6>SPTS, queue 0 extended.
<6>PES, queue 0 normal.
<6>SPTS, queue 0 extended.
<6>SPTS, queue 0 extended.
<6>SPTS, queue 0 extended.
<6>SPTS, queue 0 extended.
<3>hda: lost interrupt
<4>hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
<4>
<3>hda: drive not ready for command
<6>SPTS, queue 0 extended.
<4>not clipmode: queue 4 pid: 0x0100
<6>PES, queue 0 normal.
<4>avia_av_wdt_thread: video decoding stopped ==> restart
<6>SPTS, queue 0 extended.