seit gestern habe ich das Problem, dass meine Box über Astra nicht mehr wirklich brauchbare Programme empfängt. Zum Beispiel RTL, Pro7, ARD, ZDF, usw.
Lediglich die Programme EinsExtra, EinsFestival, EinsPlus, ARTE, Phoenix und Test-R sind verfügbar. Über Eutelsat kommt jede Menge an fremden rein.
Seltsam war auch, dass am Ende die Box automatisch zwischen Arte und einem der ARD-Kanäle Eins-x automatisch hin- und hergeschalten hat???
Nun habe ich angefangen, ein mögliches Problem zu finden:
1. Check der SAT-Schüssel – keine Veränderungen der Position
2. Check mittels eines analogen Receivers – alles gut, vermisste Programme sind alle da
3. Images neu geflasht – passt (Log habe ich unten angehängt)
4. Kanalsuche mit folgenden Einstellungen (siehe Bild1)
- a1.JPG (29.93 KiB) 2301 mal betrachtet
Die DiSEqC-Einstellungen habe ich dabei auf:
Astra 19,2°E 1
Eutelsat 13,0E° 2
5. Die Kanalsuche wird nach 15 Minuten erfolgreich abgeschlossen mit (siehe Bild2)
- a.png (288.55 KiB) 2301 mal betrachtet
6. Vermisste Sender sind wieder nicht mit dabei
Nun bin ich am Ende mit meinen Weisheiten.
Was habe ich an Hardware?
- Dbox2 mit dem aktuellen Image vom 04. Dezember
- 80er Spiegel
- Quad-Monoblock LNB LMQP-04H(ca. ein Monat alt)
Hier nun die LOGs einmal vom Flashen und das vom Booten. Über hilfreiche Tipps würde ich mich mehr als freuen.
Grüße
Alex
Flash-LOG:
ûdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.1.132, My IP 192.168.1.202
debug: Sending TFTP-request for file u-boot
will verify ELF image, start= 0x800000, size= 140064
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.3.1 (Tuxbox - Hallenberg.com) (Dec 23 2007 - 22:22:21)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.1.132; our IP address is 192.168.1.202
Filename 'u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.1.132; our IP address is 192.168.1.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: ##
done
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.1.132; our IP address is 192.168.1.202
Filename 'u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.1.132; our IP address is 192.168.1.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: ####################################
done
Bytes transferred = 179877 (2bea5 hex)
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
Using SCC ETHERNET device
TFTP from server 192.168.1.132; our IP address is 192.168.1.202
Filename 'kernel-cdk'.
Load address: 0x100000
Loading: #################################################################
##########################################################
done
Bytes transferred = 626108 (98dbc hex)
Using SCC ETHERNET device
TFTP from server 192.168.1.132; our IP address is 192.168.1.202
Filename 'u-initrd'.
Load address: 0x400000
Loading: #################################################################
#################################################
done
Bytes transferred = 579075 (8d603 hex)
............................................................... done
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 626044 Bytes = 611.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 00400000 ...
Image Name: Ramdisk Image
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 579011 Bytes = 565.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Ramdisk to 01f21000, end 01fae5c3 ... OK
Linux version 2.4.36-dbox2 (Hallenberg.com) (gcc version 3.4.6) #2 So 6. Jan 18:22:41 CET 2008
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/ram rw ip=192.168.1.202:192.168.1.132:::::off
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30356k available (1048k kernel code, 324k data, 72k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGÿttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:19:57:3c
RAMDISK driver initialized: 16 RAM disks of 3333K size 1024 blocksize
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (rootfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
IP-Config: Guessing netmask 255.255.255.0
IP-Config: Complete:
device=eth0, addr=192.168.1.202, mask=255.255.255.0, gw=255.255.255.255,
host=192.168.1.202, domain=, nis-domain=(none),
bootserver=192.168.1.132, rootserver=192.168.1.132, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 565k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 72k init
init started: BusyBox v1.9.0 (2008-01-05 13:28:28 CET)
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
dbox2 - ImageFlashingAssistent 3.0
- Hallenberg.com -
Schreibe Backup: 8064k von 8064k (100%)
Lade Flashimage...
done.
Sende Backup...
Lösche Sektoren: 63 von 63 (100%)
Schreibe Daten: 8064k von 8064k (100%)
Verifziere Daten: 8064k von 8064k (100%)
Sie koennen die dbox jetzt ausschalten.
-------------------------------------------------------------
BootP: Request von 00509C19573C erhalten
Error DeleteIpNetEntry: Falscher Parameter.
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C19573C gesetzt
BootP: Antwort an 00509C19573C gesendet
TFTP: Sende C:\tmp\dbox\tftp\u-boot
TFTP: Transfer erfolgreich beendet
BootP: Request von 00509C19573C erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C19573C gesetzt
BootP: Antwort an 00509C19573C gesendet
TFTP: Sende C:\tmp\dbox\tftp\logo-lcd
TFTP: Transfer erfolgreich beendet
BootP: Request von 00509C19573C erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C19573C gesetzt
BootP: Antwort an 00509C19573C gesendet
TFTP: Sende C:\tmp\dbox\tftp\logo-fb
TFTP: Transfer erfolgreich beendet
TFTP: Sende C:\tmp\dbox\tftp\kernel-cdk
TFTP: Transfer erfolgreich beendet
TFTP: Sende C:\tmp\dbox\tftp\u-initrd
TFTP: Transfer erfolgreich beendet
TFTP: Sende C:\tmp\box\JtG_Neutrino_Komplett_2x__v2.3.4.img
TFTP: Transfer erfolgreich beendet
TFTP: Schreibe Backup nach C:\tmp\dbox\Backups\2010-03-11 18-58-06_291.img
TFTP: Transfer erfolgreich beendet
------ Zusatzinformationen ------
Gewählter Netzwerkadapter: Broadcom NetXtreme 57xx Gigabit Controller - Paketplaner-Miniport (1)
IP-Adresse des Netzwerkadapters: 192.168.1.132
IP-Adresse die die dbox bekommt: 192.168.1.202
Betriebssystem: Microsoft Windows XP Professional Service Pack 3 (Build 2600)
CPU 1: Intel(R) Pentium(R) M processor 2.00GHz @ 13 MHz
Dateiname des Images: JtG_Neutrino_Komplett_2x__v2.3.4.img
Imagetyp: Zwei Flashs
DBOX-IFA Version: 3.1
------ Powered by http://www.dboxservice-hallenberg.de ------
BOOT-LOG:
[yhttpd] !!! SIGNAL !!! :15!
[yhttpd] No special SIGNAL-Handler:15!
[yhttpd] stop requested......
Sent SIGKILL to all processes
Requesting system reboot
‘debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-e1.b8.22.07.00.00-5f
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 170380
verify sig: 262
Branching to 0x40000
U-Boot 2009.08 (Tuxbox) (04.12.09 09:04:31)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
env: found console with value ttyS0
env: found baudrate with value 9600
env: found dbox_duplex with value 0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
env: found lcd_bias with value 0
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
LCD: ready
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 671124 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
Image Name: Linux-2.4.37.7-dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 671060 Bytes = 655.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37.7-dbox2 (vom Jtg-Team) (gcc version 3.4.6) #1 Fr 4. Dez 08:
42:33 CET 2009
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600
dbox_duplex=0
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:19:57:3c
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (squashfs+lzma)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.15.2 (2009-12-04 09:15:43 CET)
starting pid 8, tty '': '/etc/init.d/rcS'
Starting the automounter
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
tuxbox: IDE-Interface detected, Vendor: Gurgel
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.100 2009/09/11 05:58:41 rhabarber1848 Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: AVIA 500 LB4 found, sptsfix is off
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
jtginfo $Id: jtginfo.c,v 2.2 2009/02/07 21:51:28 jtgriker Exp $
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
ves1x93: Detected ves1893a rev2
DVB: registering frontend 0:0 (VES1893)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Fri Dec 13 21:45:52 CET 1901
$Id: sectionsd.cpp,v 1.315 2009/11/30 21:50:26 seife Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
19:38:36.008 [timeThread] Time set via NTP, going to sleep for 1800 seconds.
[timerd] woke up from timer? false!
[timerd] using config file /var/tuxbox/config/timerd.conf
19:38:37.211 dmxSDT: going to sleep...
$Id: zapit.cpp,v 1.450 2009/11/26 20:58:21 rhabarber1848 Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0 auto_fec 0
avia_gt_core: masking unhandled irq reg 0 bit 7
/var/tuxbox/config/zapit/ubouquets.xml: No such file or directory
/tmp/currentservices.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[camd] ca system id: 1702
[CVideo::setVideoFormat] output format: 4:3(LB)
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib
/liblcddisplay.so.0)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] found esound, adding personalized esound entry to mainmenue
[network config] Instance created
loading locales: scandir: No such file or directory
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)
[neutrino] setRepeat: delay=25 period=0 use kernel-repeat: no
[neutrino] registering as event client
[scan-setup] received 31 sats
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[zapit] tuned frequency does not match request. difference: 1546
PES, queue 0 normal.
[neutrino] no file /var/tuxbox/config/init.end was found
avia_gt_core: masking unhandled irq reg 1 bit 15
[neutrino] initialized everything
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3)
19:38:56.566 eit_set_update_filter, servicekey = 0x41b00017034, current version
5
nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/l
iblcddisplay.so.0)
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
