Riker hat geschrieben:
Entweder ist dein Modemkabel defekt oder die CPU der Box, wir haben das schon oft gehabt das die Boxen
zwar mir Linux funktiuonieren aber die IRQ Leitung defekt ist die das Interface nutzt.
Unschön
![Sad :-(](./images/smilies/icon_sad.gif)
Stecken tut das Kabel einwandfrei, durchmessen könnte ich's bei nächster Gelegenheit.
Meine Box hat übers Wochenende übrigens ein halbes Dutzend Sendungen auf Sendern mit hoher
Datenrate problemlos aufgenommen. Sonntag wieder zu Hause, vesucht fernzusehen: kein Bild, kein Ton
(LOCK LOST). So habe ich meinen Zweitreceiver angeworfen - und siehe da, plötzlich hatte auch die dbox
wieder ein Bild. Sieht mir nach zu schwacher Steuerspannung fürs LNB aus?!
Um zu schauen, ob zu schwaches Netzteil das Problem sein könnte, habe ich jetzt mal provisorisch ein
externes Netzteil angehängt - weiter beobachten ist angesagt.
Schließlich hier endlich ein
Bootlog mit den lost interrupts - hoffentlich wird jemand schlauer draus als
ich - ich sehe keinen Anhaltspunkt für den Fehler.
Gruß,
Sir Toby
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-19.6b.27.07.00.00-1d
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
debug: Got Block #0004
debug: Got Block #0008
debug: Got Block #0012
debug: Got Block #0016
debug: Got Block #0020
debug: Got Block #0024
debug: Got Block #0028
debug: Got Block #0032
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 172048
verify sig: 262
Branching to 0x40000
U-Boot 2009.01 (Tuxbox) (10.02.2009 09:36:41)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
env: found "console" with value ttyS0
env: found "baudrate" with value 9600
env: found "dbox_duplex" with value 0
env: found "lcd_inverse" with value 0
env: found "lcd_contrast" with value 15
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 689542 bytes loaded to 0x100000
## Booting kernel from Legacy Image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 689478 Bytes = 673.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37-dbox2 (vom Jtg-Team) (gcc version 3.4.6) #1 Di 10. Feb 09:56:14 CET 2009
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30788k available (1172k kernel code, 348k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (
rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:19:1f:e0
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (SquashFS_LZMA)"
0x006a0000-0x00800000 : "var (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.13.2 (2009-02-10 09:54:55 CET)
Starting the automounter
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
tuxbox: IDE-Interface detected, Vendor: Unknown
udhcpc (v1.13.2) started
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Sending discover...
Sending select for 192.168.178.22...
Lease of 192.168.178.22 obtained, lease time 864000
deleting routers
route: SIOCDELRT: No such process
adding dns 192.168.178.1
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
dboxide: $Id: main.c,v 1.13 2009/01/13 22:13:23 dbt Exp $
ide: late registration of driver.
dboxide: activating cs2
dboxide: address space of IDE-Interface is at: 0xc394f000
dboxide: IDE-Interface detected, Vendor: Unknown
dboxide: sreset succeeded
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Probing IDE interface ide0...
hda: SAMSUNG HM500LI, ATA DISK drive
ide0 at 0x010-0x017,0x04e on irq 47
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 976773168 sectors (500108 MB) w/8192KiB Cache, CHS=60801/255/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
Adding Swap: 136544k swap-space (priority -1)
avia_av_core: Starting avia_av_wdt thread.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
/dev/ide/host0/bus0/target0/lun0/disc:
setting 32-bit IO_support flag to 1
setting drive write-caching to 0 (off)
setting standby to 0 (off)
IO_support = 1 (32-bit)
write-caching = 0 (off)avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_core: masking unhandled irq reg 0 bit 1
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
jtginfo $Id: jtginfo.c,v 2.2 2009/02/07 21:51:28 jtgriker Exp $
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
ves1x93: Detected ves1893a rev2
DVB: registering frontend 0:0 (VES1893)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Thu Jan 1 12:00:00 CET 1970
mmc2 Driver $Id: mmc2.c,v 1.4 2007/05/20 13:42:05 satsuse Exp $
mmc2: Hardware init
mmc: Card init
mmc: Card init *OK1*
mmc: Card init *OK2*
mmc: Media found Size = 992000, hardsectsize = 512, sectors = 1984000
mmca: p1
$Id: sectionsd.cpp,v 1.286 2009/01/24 17:34:45 seife Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 3 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 240min after their end time
/var/tuxbox/config/mybouquets.xml: No such file or directory
[timeThread] Time set via NTP, going to sleep for 1800 seconds.
[timerd] woke up from timer? false!
22:41:05.052 dmxSDT: going to sleep...
$Id: zapit.cpp,v 1.417 2009/02/09 15:17:07 rhabarber1848 Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0
avia_gt_core: masking unhandled irq reg 0 bit 7
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 41E onid 1
[...]
[getservices]: replacing 'TELEREALITE FRA' (service_id=0x2263): FAILED!
[getservices] dup transponder id 45A onid 1
/tmp/currentservices.xml: No such file or directory
[camd] ca system id: 1702
$Id: controld.cpp,v 1.132 2008/12/25 16:35:46 houdini Exp $
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[controld] format: 16:9
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[yhttpd] Webserver starting...
neutrino: /lib/libpng12.so.0: no version information available (required by neutrino)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[CFSMounter] Mount(0) 192.168.178.23:/mnt/IDE1/Video -> /mnt/filme
[CFSMounter] FS mount error: "mount -t nfs 192.168.178.23:/mnt/IDE1/Video /mnt/filme -o rw,soft,udp,nolock,rsize=8192,wsize=8192"
[neutrino] menue setup
imageinfo: JTG-Image [IDE] (2.3.2)
loading locales: scandir: No such file or directory
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)
[neutrino] setRepeat: delay=25 period=0 use kernel-repeat: no
[neutrino] received 1 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temp[LCDFONT] FTC_Face_Requester (Fix12/Regular)
22:44:16.804 dmxCN: waking up again - requested from .change()
PES, queue 0 normal.
22:44:17.849 dmxCN: going to sleep...
22:44:17.849 eit_set_update_filter, servicekey = 0x41b00017034, current version 0
hda: lost interrupt
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: lost interrupt
delete all conflict timers
no response from sectionsd
no response from sectionsd
no response from sectionsd
22:45:22.237 [sectionsd] DMX::readNbytes received POLLERR, pid 0x12, filter[4] filter 0x60 mask 0xf1
22:45:26.420 [sectionsd] DMX::readNbytes received POLLERR, pid 0x12, filter[4] filter 0x60 mask 0xf1
22:45:32.319 [sectionsd] DMX::readNbytes received POLLERR, pid 0x12, filter[4] filter 0x60 mask 0xf1
no response from sectionsd
no response from sectionsd
no response from sectionsd
hda: lost interrupt
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
22:45:41.985 [sectionsd] DMX::readNbytes received POLLERR, pid 0x12, filter[4] filter 0x60 mask 0xf1
22:45:47.443 [sectionsd] DMX::readNbytes received POLLERR, pid 0x12, filter[4] filter 0x60 mask 0xf1
hda: lost interrupt
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
usw... habe die Box dann runtergefahren
[timeThread] Time set via NTP, going to sleep for 1800 seconds.
[eventserver]: connect (/tmp/neutrino.sock): Connection refused
zapit shot down
![Smile :)](./images/smilies/icon_smile.gif)
Going to halt system now ...
CXA2092 found
CXA2092 found
Unmounting 'ext2' on '/hdd'
Unmounting 'tmpfs' on '/tmp'
umount: can't umount /tmp: Device or resource busy
Unmounting 'jffs2' on '/var'
Ready to shutdown system...
The system is going down NOW!
Sending SIGTERM to all processes
[yhttpd] !!! SIGNAL !!! :15!
[yhttpd] No special SIGNAL-Handler:15!
[yhttpd] stop requested......
Sending SIGKILL to all processes
Requesting system halt
flushing ide devices: hda